Table of Contents
When your Samsung Galaxy Tab 2’s battery isn’t working properly, it’s time to replace it. In this blog post, we’ll explain how to replace a battery in a Samsung Galaxy Tab 2 and provide tips for maximizing your device’s lifespan. By following our guide, you’ll be able to keep your Samsung Galaxy Tab 2 running smoothly and enjoy long-term battery life.
How Do You Know When Your Battery Needs Replacing?
It isn’t possible to keep batteries for a lifetime. Over time, your battery degrades as you charge and discharge it, resulting in less battery life. Batteries or devices need to be replaced eventually.
Battery performance stays the same from day to day. Over time, batteries gradually degrade. A gradual capacity decrease occurs over many charge cycles, so you might notice it once you realize you used to get a few more hours of battery power.
Maintaining your battery properly can prolong its life and keep its capacity high. However, you can only tolerate battery degradation for a while if you replace your devices frequently.
How To Replace Battery Samsung Galaxy Tab 2
The lithium-ion batteries in Samsung’s Galaxy Tab wear out over time and must be replaced. A drastically reduced battery life and sudden shutdowns are signs that you need to replace your Galaxy Tab’s battery.
Removing the Battery From a Samsung Galaxy Tab2
- Make sure you have the right equipment. A plastic pry tool and a tiny screwdriver are needed to remove the battery from a Samsung Galaxy Tab. Tri-wing screwdrivers are required for some models.
A replacement battery kit with all the tools is also available, as is a kit that includes all the tools and a replacement battery. Ensure you get the right battery or kit for your Samsung Galaxy Tab2.
- Purchasing the correct kit for your Samsung Galaxy Tab model is important. Batteries and tools may be included in the right kit.
- Alternatively, you can use a guitar pick or a thin slice of plastic cut from a soda bottle if you don’t have a plastic pry tool.
- Shut down your Galaxy Tab 2. You can power off your tab unit by pressing and holding the power button.
- Remove the two screws near the charging port. There are screws on both sides of the charging port on Galaxy Tab 2 models. To remove the screws from your Galaxy Tab model with screws on the sides of the charging port, use a safety pin or sharp object to remove the screw covers.
- To remove the back cover, use the plastic pry tool. The plastic pry tool should be inserted between the back and front cover. The device usually has this along its side edges. Depending on the model, it may be on the front of the screen. Apply pressure around the entire device to separate the front cover from the back.
Go slowly and carefully, as the clips that attach the back cover are easy to break. When separating the front panel from the Galaxy Tab’s top left corner, be careful not to tear the microphone cable.
- Disassemble the unit by separating the back cover. Remove the back cover once all the clips have popped out.
- Ribbon cables and batteries should be tape-free. Ribbon cable connectors and batteries may be covered with tape. The plastic pry tool can be used to remove the tape. Set it aside after you’ve removed it.
- Remove the ribbon cables covering the battery. To remove the ribbon cables, use the plastic pry tool for popping the tab on the connectors. Slide the ribbon cables out of the connectors. The ribbon cables can be slid out if there is no tab on the connectors.
- Ensure that the battery screws are removed. Galaxy Tab2 models have screwed-in batteries. Remove the screws on all sides of the battery using a tiny Phillips screwdriver.
- Remove the battery from the board. Four wires from the battery connect to a black clip on the mainboard. To disconnect the wire clip from the board, place the plastic pry tool under the wires and apply upward pressure.
- It is necessary to remove the battery. To remove the battery, lift it out once it has been disconnected.
Reassembling Your Samsung Galaxy Tab2
- You need to insert a new battery. Replace the old battery with the new one after removing the old one.
- The battery wires were attached to the board. The four wires from the battery are attached to a black clip. Attach the battery to the board by gently pressing down on the black clip.
- It is important to reattach the battery screws. Use a tiny Phillips screwdriver to secure the new battery if the old one was screwed in place.
- Reinstall the ribbon cables. Lay the ribbon connectors over the battery if your Samsung Galaxy Tab has them. Slide the ribbon cables back into place until they are firmly seated, ensuring the connector tabs are up. Ensure that the connector tabs are locked in place by pressing down on them.
- Warning: A loose ribbon cable will cause your device to perform poorly.
- Recover the ribbon connectors and battery with tape. Put the tape back on the ribbon connectors and battery if it covered them.
- Attach the back cover again. Put the back cover over the unit after the battery and cables are securely attached. Apply a little pressure around the edges to snap the back cover back.
- It was necessary to reattach the screws. To reattach screws to your Samsung Galaxy Tab model, use a Tri-wing screwdriver. Afterward, replace the screws with their covers. The Samsung Galaxy Tab has now been reassembled. It can be powered on.
How To Maximize The Lifespan Battery Samsung Galaxy Tab 2
Battery life depends on the device’s use, and different devices have different battery lives. These tips will help you care for your battery and get the most out of it in everyday use.
- Turn down the brightness of the display.
- Remove unused apps by closing, disabling, or uninstalling them.
- You can turn off Always On Display (AOD) or set a schedule.
- Ensure WiFi, Bluetooth, and GPS are turned off when not in use.
- Activate the power saving mode.
- Update your device’s software.
- Be sure to check your device’s signal bars.
- Sync your device regularly by checking how often it synchronizes
- Make sure your battery is not fully discharged.
- Make sure your device is properly stored. Batteries can be damaged by extreme heat and cold. So it would help if you stored your tab properly.
Frequently Asked Questions (FAQ)
Why Is My Samsung Galaxy Tab 2 Won’t Charge?
In most cases, Samsung tablets don’t charge because of a faulty cable, charging block, charger cable, or adapter. The charging port is clogged with dirt or debris. Interruptions in the charging process caused by third-party apps.
How Do You Fix A Samsung Galaxy Tab 2 That Won’t Turn On?
Most often, the power button is pressed for 15-30 seconds, or the home, volume down, or up, and power buttons are pressed simultaneously for 10-20 seconds. The power button is pressed, and the screen is touched. Another charger and cable may work, or power and volume up/down can be pressed while charging.
How Do I Revive A Dead Samsung Tablet?
A frozen or unresponsive device needs to be restarted. For more than 7 seconds, press and hold the Power and Volume down buttons simultaneously. To shut down the device, press and hold the Power button for up to two minutes.
Why Is My Battery Dying So Fast On My Samsung Tablet?
Too many push notifications and alerts are depleting the battery. Apps that run location services should be more numerous. The background is overloaded with apps. Too much light is coming from the screen.
Replacing a battery in a Samsung Galaxy Tab 2 is a simple and easy process that can help you keep your device running smoothly and enjoy long-term battery life. By following our guide, you’ll be able to replace your battery without any hassle or difficulty. If you have any questions or would like more information on this topic, you can read our related article.
You May Like To Read Also:
Leave a Reply
You must be logged in to post a comment.